Just How to Install a Bathtub: Set Up an Acrylic Tub and Bathtub Surround
Just How to Install a Bathtub: Set Up an Acrylic Tub and Bathtub Surround
Blog Article
The article down below involving How to Install a Bathtub: Install an Acrylic Tub and Tub Surround is especially stimulating. You should investigate for yourself.
Mounting a bath tub isn't specifically rocket science, but it does require solid plumbing, carpentry, and in some cases, tiling skills. Replacing an old tub with a new one is likewise a moderately challenging job. If the old tub is easily available, the project can move rapidly; if you have to open a wall to remove the old tub and position the brand-new bath tub, the job is a lot harder. In either instance, the job is within a house handyman's skills, although you will certainly require an assistant to leave the old tub as well as set in the new one. Make sure you have actually certified on your own for the task as well as are comfortable attempting it. Rather than working with a contractor to take control of a halfway-completed task, it is much better to think about employing one before you start. Opportunities are you might need a professional plumber to make tube connections.
This write-up will certainly assist you install a new bath tub in your shower room if you have already bought a brand-new bathtub as well as don't require to alter the arrangement of your previous water supply pipelines.
Your tools and product list ought to comprise the following:
Removing Old Taps
If you need to change old faucets with new ones as a part of your installation, then the first thing you need to do is disconnect the water supply. After doing so, activate the faucets to drain any kind of water staying in the system. The process of getting rid of the existing taps can be fairly troublesome due to the limited gain access to that is frequently the instance.
Use a container wrench (crowsfoot spanner) or a tap tool to reverse the nut that links the supply pipes to the faucets. Have a fabric ready for the continuing to be water that will certainly come from the pipelines. When the supply pipes have actually been eliminated, use the exact same tool to loosen up the nut that holds the faucets onto the bath/basin. You will require to stop the solitary taps from transforming during this procedure. Once the faucets have been gotten rid of, the holes in the bath/basin will have to be cleansed of any type of old sealing substance.
Before carrying on to fit the new faucets, compare the pipeline connections on the old faucets to the new faucets. If the old faucets are longer than the new faucets, then a shank adapter is needed for the brand-new taps to fit.
Suitable New Taps
If the tails of the new faucets are plastic, then you will certainly need a plastic adapter to avoid damages to the thread. One end of the port fits on the plastic tail of the faucet as well as the other end supplies a connection to the current supply pipes.
If you require to fit a monobloc, then you will certainly require lowering couplers, which connects the 10mm pipe of the monobloc to the typical 15mm supply pipe.
Next off, position the faucet in the mounting opening in the bath/basin ensuring that the washing machines remain in place in between the faucet as well as the sink. Safeguard the tap in position with the manufacturer supplied backnut. As soon as the tap is firmly in place, the supply pipes can be attached to the tails of the taps. The faucets can either be attached by using corrugated copper piping or with typical faucet connectors. The previous kind ought to be linked to the faucet ends first, tightening up just by hand. The supply pipes can later on be attached to the other end. Tighten both ends with a spanner after both ends have actually been attached.
Installing the Bathtub
Utilizing both wood boards under its feet, position the bathtub in the required setting. The wooden boards are practical in equally spreading out the weight of the bathtub over the area of the boards rather than focusing all the weight onto 4 small points.
The next objective is to make certain that the bath tub is leveled all round. This can be achieved by inspecting the level and also adjusting the feet on the bathtub up until the level reviews degree.
To install taps, fit the bottom of the furthest versatile faucet adapter to the appropriate supply pipe by making a compression join; then do the exact same for the various other faucet.
Activate the water supply and check all joints as well as brand-new pipework for leakages and also tighten them if essential. Load the bath tub and also check the overflow outlet and the normal outlet for leaks.
Finally, deal with the bathroom paneling as defined in the supplier's user's manual. Tiling as well as sealing around the bathtub needs to wait up until the bathtub has actually been made use of at the very least once as this will certainly resolve it right into its final position.
Preparing for the Installment
To start with, the sustaining framework supplied with the bathroom needs to be fitted (if needed) according to the producer's instructions. Next, fit the faucets or mixer to the tub. When fitting the tap block, it is necessary to make certain that if the tap comes with a plastic washing machine, it is fitted in between the bath and the faucets. On a plastic bath, it is also practical to fit a supporting plate under the faucets device to avoid strain on the bath tub.
Fit the versatile tap adapters to the bottom of both taps making use of 2 nuts as well as olives (in some cases provided with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet opening, and then pass the electrical outlet with the hole in the bathroom. Use the nut provided by the maker to fit the plug-hole. Analyze the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next, fit completion of the flexible overflow pipe to the overflow electrical outlet. Afterwards, screw the pipe to the overflow face which must be fitted inside the bath. See to it you utilize every one of the provided washers.
Link the trap to the bottom of the waste electrical outlet on the bathtub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, as well as screw on the trap to the electrical outlet. Connect all-time low of the overflow tube in a similar manner.The bathroom should currently be ready to be suited its final setting.
Tiling Around the Bathtub
In the location where the bath satisfies the tile, it is needed to seal the joins with a silicone rubber caulking. This is important as the fitting can relocate enough to fracture a rigid seal, creating the water to penetrate the wall surface in between the bath and also the tiling, resulting in complications with wetness and feasible leaks to the ceiling listed below.
You can choose from a selection of coloured sealants to assimilate your fixtures as well as installations. They are offered in tubes and also cartridges, as well as can sealing voids as much as a size of 3mm (1/8 inch). If you have a larger space to fill, you can load it with spins of soaked paper or soft rope. Remember to constantly fill the tub with water prior to sealing, to allow for the motion experienced when the bathtub is in usage. The sealant can split rather early if you do not think about this movement before securing.
Alternatively, ceramic coving or quadrant ceramic tiles can be made use of to edge the bath or shower tray. Plastic strips of coving, which are easy to use as well as reduce to size, are additionally easily readily available on the market. It is a good idea to fit the tiles utilizing waterproof or water resistant glue and cement.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
As a devoted reader on How to Install a Bathtub Yourself, I thought sharing that excerpt was really useful. Please take the opportunity to distribute this article if you liked it. Kudos for your time. Don't hesitate to stop by our blog back soon.
Schedule
Report this page